20A Kitchen Outlet Circuit — Wire Size Guide
Dedicated 20-amp kitchen countertop receptacle circuit. The NEC requires at least two 20-amp small-appliance branch circuits to serve kitchen countertop outlets. These circuits power countertop appliances such as toasters, blenders, mixers, and coffee makers. No other outlets may be connected to these circuits.
Copper Wire Size by Distance
The table below shows the recommended copper wire gauge for a 20A Kitchen Outlet Circuit circuit (120V, 20A, Single-Phase) at various one-way distances from the panel. Two voltage drop limits are shown: 3% for branch circuits and 5% for feeder-plus-branch combined. The ampacity column is based on NEC Table 310.16 at 75 degrees C. When the 3% and 5% columns show different gauges, the distance is long enough that voltage drop — not ampacity — is the controlling factor, and you must use the gauge appropriate for your circuit type.
| Distance | 3% Drop Gauge | 3% Drop (V) | 3% Drop (%) | 5% Drop Gauge | 5% Drop (V) | 5% Drop (%) |
|---|---|---|---|---|---|---|
| 25 ft | 14 AWG | 3.14 | 2.62% | 14 AWG | 3.14 | 2.62% |
| 50 ft | 10 AWG | 2.48 | 2.07% | 12 AWG | 3.96 | 3.30% |
| 75 ft | 8 AWG | 2.33 | 1.95% | 12 AWG | 5.94 | 4.95% |
| 100 ft | 8 AWG | 3.11 | 2.59% | 10 AWG | 4.96 | 4.13% |
| 125 ft | 6 AWG | 2.46 | 2.05% | 8 AWG | 3.89 | 3.24% |
| 150 ft | 6 AWG | 2.95 | 2.46% | 8 AWG | 4.67 | 3.89% |
| 200 ft | 4 AWG | 2.46 | 2.05% | 6 AWG | 3.93 | 3.27% |
| 250 ft | 4 AWG | 3.08 | 2.57% | 6 AWG | 4.91 | 4.09% |
| 300 ft | 3 AWG | 2.94 | 2.45% | 6 AWG | 5.89 | 4.91% |
| 400 ft | 2 AWG | 3.10 | 2.59% | 4 AWG | 4.93 | 4.11% |
| 500 ft | 1 AWG | 3.08 | 2.57% | 3 AWG | 4.90 | 4.08% |
Aluminum Wire Size by Distance
Aluminum conductors cost less and weigh less than copper but have higher resistance, requiring larger gauge sizes to carry the same current. The table below shows the recommended aluminum wire gauge for this 20A Kitchen Outlet Circuit circuit at various distances. Aluminum is a practical choice for longer feeder runs and service entrance conductors where the material savings justify the larger conductor size. All aluminum terminations must be rated for aluminum use (AL-CU marking) and treated with anti-oxidant compound.
| Distance | 3% Drop Gauge | 3% Drop (V) | 3% Drop (%) | 5% Drop Gauge | 5% Drop (V) | 5% Drop (%) |
|---|---|---|---|---|---|---|
| 25 ft | 12 AWG | 3.25 | 2.71% | 12 AWG | 3.25 | 2.71% |
| 50 ft | 8 AWG | 2.56 | 2.13% | 10 AWG | 4.08 | 3.40% |
| 75 ft | 6 AWG | 2.42 | 2.02% | 8 AWG | 3.84 | 3.20% |
| 100 ft | 6 AWG | 3.23 | 2.69% | 8 AWG | 5.12 | 4.27% |
| 125 ft | 4 AWG | 2.54 | 2.12% | 6 AWG | 4.04 | 3.37% |
| 150 ft | 4 AWG | 3.05 | 2.54% | 6 AWG | 4.85 | 4.04% |
| 200 ft | 3 AWG | 3.22 | 2.69% | 4 AWG | 4.06 | 3.39% |
| 250 ft | 2 AWG | 3.19 | 2.66% | 4 AWG | 5.08 | 4.23% |
| 300 ft | 1 AWG | 3.04 | 2.53% | 3 AWG | 4.84 | 4.03% |
| 400 ft | 1/0 AWG | 3.22 | 2.68% | 2 AWG | 5.10 | 4.25% |
| 500 ft | 2/0 AWG | 3.18 | 2.65% | 1 AWG | 5.06 | 4.22% |
Installation Tips for 20A Kitchen Outlet Circuit
Proper installation is just as important as selecting the correct wire size. The following tips address the key NEC requirements and best practices specific to 20a kitchen outlet circuit circuits. Always verify these requirements against the current edition of the NEC and your local code amendments before beginning work.
- This is a required dedicated circuit per the NEC. It cannot serve other rooms or areas of the dwelling.
- All wire connections must be made with listed connectors and torqued to manufacturer specifications. Use anti-oxidant compound on all aluminum connections.
- Verify local code amendments, as your jurisdiction may have requirements beyond the NEC minimum. Always pull a permit and schedule inspections for electrical work.
NEC Code References
The 20A Kitchen Outlet Circuit circuit is governed by NEC 210.11(C)(1), 210.52(B). These NEC sections specify the minimum requirements for circuit sizing, overcurrent protection, grounding, and installation methods. The wire sizing in this guide is based on the following NEC tables and articles:
- NEC Table 310.16 — Ampacity of insulated conductors rated 0-2000V in raceways, cables, or direct buried. Provides the maximum current each gauge can safely carry at 60, 75, and 90 degrees C.
- NEC Chapter 9, Table 8 — Conductor properties including DC resistance per 1000 feet for uncoated copper and aluminum. These resistance values are used in the voltage drop formula.
- NEC 210.19(A) Informational Note No. 4 — Recommends that branch circuit conductors be sized so that the voltage drop does not exceed 3%, and the combined feeder plus branch circuit drop does not exceed 5%.
- NEC 215.2(A)(1) Informational Note No. 2 — Same voltage drop recommendation applied to feeder conductors.
- NEC 210.11(C)(1), 210.52(B) — Specific requirements for this application, including circuit sizing, overcurrent protection, and installation methods.
Other Applications
Browse wire sizing guides for other common electrical circuits. Each page includes pre-computed wire sizes at multiple distances, installation tips, and NEC code references.